收藏本站
CAT4238
Table 3. DC ELECTRICAL CHARACTERISTICS
(V IN = 3.6 V, ambient temperature of 25 ° C (over recommended operating conditions unless otherwise specified))
Symbol
I Q
I SD
V FB
Parameter
Operating Current
Shutdown Current
FB Pin Voltage
Test Conditions
V FB = 0.2 V
V FB = 0.4 V (not switching)
V SHDN = 0 V
10 LEDs with I LED = 20 mA
Min
285
Typ
0.6
0.1
0.1
300
Max
1.5
0.6
1
315
Units
mA
m A
mV
I FB
FB pin input leakage
1
m A
I LED
V IH
V IL
F SW
DC
Programmed LED Current
SHDN Logic High
SHDN Logic Low
Switching Frequency
Maximum Duty Cycle
R1 = 10 W
R1 = 15 W
R1 = 20 W
Enable Threshold Level
Shutdown Threshold Level
VIN = 3 V
28.5
19
14.25
0.4
0.8
30
20
15
0.8
0.7
1.0
92
31.5
21
15.75
1.5
1.3
mA
V
MHz
%
I LIM
R SW
I LEAK
Switch Current Limit
Switch “On” Resistance
Switch Leakage Current
I SW = 100 mA
Switch Off, V SW = 5 V
350
450
1.0
1
600
2.0
5
mA
W
m A
Thermal Shutdown
Thermal Hysteresis
150
20
° C
° C
V UVLO
V OV-SW
Undervoltage Lockout (UVLO) Threshold
Overvoltage Detection Threshold
1.9
40
V
V
V OCL
Output Voltage Clamp
“Open LED” with VIN = 5 V
43
45
48
V
Pin Description
VIN is the supply input for the internal logic. The device is
compatible with supply voltages down to 2.8 V and up to
5.5 V. It is recommended that a small bypass ceramic
capacitor (4.7 m F) be placed between the VIN and GND pins
near the device. If the supply voltage drops below 1.9 V, the
device stops switching.
SHDN is the shutdown logic input. When the pin is tied to
a voltage lower than 0.4 V, the device is in shutdown mode,
drawing nearly zero current. When the pin is connected to a
voltage higher than 1.5 V, the device is enabled.
GND is the ground reference pin. This pin should be
SW pin is connected to the drain of the internal CMOS
power switch of the boost converter. The inductor and the
Schottky diode anode should be connected to the SW pin.
Traces going to the SW pin should be as short as possible
with minimum loop area. An over-voltage detection circuit
is connected to the SW pin. When the voltage reaches 40 V,
the device enters a low power operating mode preventing the
SW voltage from exceeding the maximum rating.
FB feedback pin is regulated at 0.3 V. A resistor connected
between the FB pin and ground sets the LED current
according to the formula:
connected directly to the ground place on the PCB.
I LED +
0.3 V
R 1
The lower LED cathode is connected to the FB pin.
Table 4. PIN DESCRIPTIONS
Pin #
1
2
3
4
5
Name
SW
GND
FB
SHDN
VIN
Function
Switch pin. This is the drain of the internal power switch.
Ground pin. Connect the pin to the ground plane.
Feedback pin. Connect to the last LED cathode.
Shutdown pin (Logic Low). Set high to enable the driver.
Power Supply input.
http://onsemi.com
3
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
CAT4240TD-GT3 IC LED DRVR WHITE BCKLGHT TSOT-5
CAT93C56XI IC EEPROM 2KBIT 2MHZ 8SOIC
CAT93C66XI IC EEPROM 4KBIT 2MHZ 8SOIC
CAT93C86LI-G IC EEPROM 16KBIT 3MHZ 8DIP
CAT9532WI-T1 IC LED DRIVER LINEAR 24-SOIC
CAT9552HV6I-TG2 IC LED DRIVER LINEAR 24-TQFN
CAV24C02YE-GT3 IC EEPROM I2C SRL 2KB 8TSSOP
CAV24C04YE-GT3 IC EEPROM 4KB I2C SER 8TSSOP
相关代理商/技术参数
CAT4238TD-GT3 制造商:ON Semiconductor 功能描述:IC LED DRIVER BOOST TSOT-23-5 制造商:ON Semiconductor 功能描述:IC, LED DRIVER, BOOST, TSOT-23-5
CAT4238TDI-G 制造商:ON Semiconductor 功能描述:IC 10-LED DRIVER LOW NOISE BOOST
CAT4240 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:6 Watt Boost LED Driver
CAT4240_0711 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:6 Watt Boost LED Driver
CAT4240AEVB 功能描述:BOARD EVALUATION DPP CAT4240A RoHS:是 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:* 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD
CAT4240AGEVB 制造商:ON Semiconductor 功能描述:EVAL BD FOR LED DRIVER - Bulk 制造商:ON Semiconductor 功能描述:BOARD EVAL FOR CAT4240
CAT4240TD-GT3 功能描述:LED照明驱动器 High Voltage Boost 2 Watt RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
CAT4240TD-GT3 制造商:ON Semiconductor 功能描述:IC LED DRIVER BOOST TSOT-23-5 制造商:ON Semiconductor 功能描述:IC, LED DRIVER, BOOST, TSOT-23-5